PIC16F785-I/SS【PDF 33/206 页】IC PIC MCU FLASH 2KX14 20SSOP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3887

29页 30页 31页 32页 [33页]34页 35页 36页 37页

128

8272E–AVR–04/2013

ATmega164A/PA/324A/PA/644A/PA/1284/P

operation. However, due to the symmetric feature of the dual-slope PWM modes, these modes

are preferred for motor control applications.

The PWM resolution for the phase correct PWM mode can be fixed to 8-, 9-, or 10-bit, or defined

by either ICRn or OCRnA. The minimum resolution allowed is 2-bit (ICRn or OCRnA set to

0x0003), and the maximum resolution is 16-bit (ICRn or OCRnA set to MAX). The PWM resolu-

tion in bits can be calculated by using the following equation:

In phase correct PWM mode the counter is incremented until the counter value matches either

one of the fixed values 0x00FF, 0x01FF, or 0x03FF (WGMn3:0 = 1, 2, or 3), the value in ICRn

(WGMn3:0 = 10), or the value in OCRnA (WGMn3:0 = 11). The counter has then reached the

TOP and changes the count direction. The TCNTn value will be equal to TOP for one timer clock

cycle. The timing diagram for the phase correct PWM mode is shown on Figure 16-8. The figure

shows phase correct PWM mode when OCRnA or ICRn is used to define TOP. The TCNTn

value is in the timing diagram shown as a histogram for illustrating the dual-slope operation. The

diagram includes non-inverted and inverted PWM outputs. The small horizontal line marks on

the TCNTn slopes represent compare matches between OCRnx and TCNTn. The OCnx Inter-

rupt Flag will be set when a compare match occurs.

Figure 16-8. Phase Correct PWM mode, timing diagram.

The Timer/Counter Overflow Flag (TOVn) is set each time the counter reaches BOTTOM. When

either OCRnA or ICRn is used for defining the TOP value, the OCnA or ICFn Flag is set accord-

ingly at the same timer clock cycle as the OCRnx Registers are updated with the double buffer

value (at TOP). The Interrupt Flags can be used to generate an interrupt each time the counter

reaches the TOP or BOTTOM value.

When changing the TOP value the program must ensure that the new TOP value is higher or

equal to the value of all of the Compare Registers. If the TOP value is lower than any of the

Compare Registers, a compare match will never occur between the TCNTn and the OCRnx.

Note that when using fixed TOP values, the unused bits are masked to zero when any of the

PCPWM

TOP

log

-----------------------------------

OCRnx/TOP Update and

OCnA Interrupt Flag Set

or ICFn Interrupt Flag Set

(Interrupt on TOP)

TOVn Interrupt Flag Set

(Interrupt on Bottom)

TCNTn

Period

OCnx

(COMnx1:0 = 2)

(COMnx1:0 = 3)

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式